insurance now klr comparison test in rider

[Jud]

My Mark III gets BreakFree too, about once every 1000 rounds. Cleaning it that often, I have to read the manual every time to take it apart and put it back together.

--- In DSN_KLR650@yahoogroups.com, RobertWichert wrote: > > Jet engine oil? Where can I get that? > > (I use BreakFree too) > > > Robert Wichert P.Eng. LEED AP BD&C > +1 916 966 9060 > FAX +1 916 966 9068 > > > > > > > > =============================================== > > > On 5/7/2012 9:26 PM, revmaaatin wrote: > > > > > > The Exxon jet engine (syn) oil (reportedly) also has significant anti > > corossion characteristics. I never used it but my jet engine mechanics > > thought it was the bomb. Perhaps others could comment/experience. > > > > The problem with most lubricants (for short range) hunting firearms is > > the balance between lubricant smell and rust. The deer can smell most > > lubricants a long ways off, at least directly downwind. > > > > Oh, and don't let your buddy pour fox urnine on your pants just before > > you walk into the woods to mask your scent.... > > > > revmaaatin. > > > > --- In DSN_KLR650@yahoogroups.com > > , Jeff Khoury wrote: > > > > > > In the USCG we used BreakFree CLP, and I have used on my personal > > firearms ever since. > > > > > > > > > Once I saw how well it protected blued steel firearms in a salt > > air/spray enviroment I was sold. It would take a lot to change me over > > to something else. > > > > > > -Jeff Khoury > > > > > > > > > ----- Original Message ----- > > > From: "eddie" > > > To: "Ron Criswell" > > > Cc: "KLR650 list" DSN_KLR650@yahoogroups.com > > > > > > Sent: Monday, May 7, 2012 3:37:00 AM > > > Subject: Re: [DSN_KLR650] NKLR: More Oops > > > > > > > > > > > > > > > > > > > > > I use Hoppe's #9 solvent or Ballistol(what the Ruger service center > > uses). > > > Oh! And dollar store Q-tips by the handful! LOL > > > eddie > > > > > > > [Original Message] > > > > From: Ron Criswell < roncriswell@ > > > > > To: transalp1@ < transalp1@ > > > > > Cc: KLR650 list < DSN_KLR650@yahoogroups.com > > > > > > > Date: 5/7/2012 6:15:51 AM > > > > Subject: Re: [DSN_KLR650] NKLR: More Oops > > > > > > > > What do you use to clean it? A friend who is a bonefied war hero > > swears > > > by.....what else....WD-40. > > > > > > > > Criswell > > > > > > > > Sent from my iPad > > > > > > > > On May 6, 2012, at 8:42 AM, "eddie" < transalp1@ > wrote: > > > > > > > > > > > > > > I bought a Ruger MkIII .22 seven years ago and the owner's > > manual was > > > very > > > > > specific about making sure the firing pin stop pin be in place > > before > > > reassembly. > > > > > If left out, the 1st time you dry-fire the weapon (normal decocking > > > procedure before disassembly, etc...), > > > > > the firing pin will overtravel and strike the chamber face - > > dinging it > > > and effectively ruining the pistol. > > > > > I've taken it apart dozen and dozen of times without incident. > > > > > Last night, after instructing my girlfriend on this important > > step with > > > her new Mk III, I dry fired my Ruger before > > > > > putting it away and then discovered the firing pin stop sitting > > among > > > my cleaning materials. > > > > > $#@%!!! > > > > > Sure enough, there was a tiny burr in the chamber face and a bullet > > > would > > > > > not go in. I gritted my teeth and took a round chainsaw file and > > *VERY > > > CAREFULLY* > > > > > removed it. It worked! Whew! The firing pin was undamaged, > > thankfully. > > > > > eddie > > > > > > > > > > > > > > > [Non-text portions of this message have been removed] >