Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order,
or if they can be found in any hardware store.
I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar
I am building.
TIA
Randy from Burbank
[Non-text portions of this message have been removed]
2000 klr will not idle or run under 2500 rpm
-
- Posts: 684
- Joined: Tue Mar 31, 2009 11:08 am
front disk rotor bolts
I don't know if the KLR is different from every other bike I've worked on, but normally they're standard Nylock nuts.
-Jeff Khoury
Astatic Solutions, LLC.
----- Original Message ----- From: "Randall Marbach" To: "KLR Group" DSN_klr650@yahoogroups.com> Sent: Saturday, August 29, 2009 9:50:48 PM GMT -08:00 US/Canada Pacific Subject: [DSN_KLR650] Front Disk Rotor Bolts Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order, or if they can be found in any hardware store. I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar I am building. TIA Randy from Burbank [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
-
- Posts: 366
- Joined: Tue Dec 04, 2001 11:54 pm
front disk rotor bolts
Nope, the nylock nuts are for the rear sprocket. The rotor bolts have a shoulder that center them in the mounting holes on the disc. I've never tried to source them so I can't be of much help there. But if you have a local place with a decent selection of metric hardware, why not just pull one from your front wheel when you get to the store and see what the friendly folks have to say about a match.
da Vermonster
--- In DSN_KLR650@yahoogroups.com, Jeff Khoury wrote: > > I don't know if the KLR is different from every other bike I've worked on, but normally they're standard Nylock nuts. > > -Jeff Khoury > Astatic Solutions, LLC. > > ----- Original Message ----- > From: "Randall Marbach" > > Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order, > or if they can be found in any hardware store. > > I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar > I am building. > > TIA > > Randy from Burbank >
-
- Posts: 15
- Joined: Thu Aug 27, 2009 10:36 am
front disk rotor bolts
--- In DSN_KLR650@yahoogroups.com, Randall Marbach wrote: I have only found them from the dealer. > > Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order, > or if they can be found in any hardware store. > > I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar > I am building. > > TIA > > Randy from Burbank > > > > > > [Non-text portions of this message have been removed] >
-
- Posts: 27
- Joined: Wed Oct 18, 2006 11:56 am
2000 klr will not idle or run under 2500 rpm
yes carb was removed and replaced with a known good one. choke cable was replaced at the same time with a different one.
klr6502k
-- In DSN_KLR650@yahoogroups.com, Richard Decker wrote:
> > Sounds to me like your choke is stuck on. Have you tried removing the choke > cable? It could be that it's stuck and pulling your choke slightly. > > On Mon, Aug 31, 2009 at 10:39 AM, klr6502k wrote:
Who is online
Users browsing this forum: No registered users and 23 guests