Page 1 of 1
rear shock setting
Posted: Wed Nov 21, 2007 9:18 pm
by gust0261
Should I follow the recommendations from the manual that came with my
07 klr 650 or put the shock settings at a higher number? I ask
because I have hit my license plate with the wheel 4 or 5 times now.
the last time it was torn off. I want to be safe on the road but have
it work like a dirt bike off road as I do ride off road most of the
time. I don't want to make it more dangerous on the road though. I
don't mind crashing in the dirt but I don't really want to while on
the road.
rear shock setting
Posted: Wed Nov 21, 2007 10:57 pm
by Jud Jones
--- In
DSN_KLR650@yahoogroups.com, "gust0261" wrote:
>
> Should I follow the recommendations from the manual that came with my
> 07 klr 650 or put the shock settings at a higher number? I ask
> because I have hit my license plate with the wheel 4 or 5 times now.
> the last time it was torn off. I want to be safe on the road but have
> it work like a dirt bike off road as I do ride off road most of the
> time. I don't want to make it more dangerous on the road though. I
> don't mind crashing in the dirt but I don't really want to while on
> the road.
>
Adjust your preload so that the rear sags about 3" from fully extended with you and your
luggage seated on the bike. Relocate your license plate to the rear fender, just below the
taillight; use a Dremel to remove the inner fender. You could just bend your plate out to clear
the wheel, or mount it in the lower holes, but sooner or later your tire will likely eat the inner
fender and force you to relocate the plate anyway.
rear shock setting
Posted: Wed Nov 21, 2007 11:06 pm
by Jeff Saline
On Thu, 22 Nov 2007 03:18:56 -0000 "gust0261"
writes:
> Should I follow the recommendations from the manual that came with
> my
> 07 klr 650 or put the shock settings at a higher number? I ask
> because I have hit my license plate with the wheel 4 or 5 times now.
>
> the last time it was torn off. I want to be safe on the road but
> have
> it work like a dirt bike off road as I do ride off road most of the
> time. I don't want to make it more dangerous on the road though.
> I
> don't mind crashing in the dirt but I don't really want to while on
> the road.
<><><><><><><><>
<><><><><><><><>
Michael,
It's probably not the shock settings that are the problem. I'd guess
it's the license plate being in the stock location.
Many folks relocate the plate higher so it touches the bottom of the rear
light. In South Dakota we get four holes in our plates so I just use the
lower holes to mount the plate. Once that's done you won't be hitting
the plate with the rear wheel.
I've found the suggested settings in the owners manual are a good
starting point. But then experimenting a bit will help you figure out
what you like for your riding conditions and style.
Best,
Jeff Saline
ABC # 4412 South Dakota Airmarshal
Airheads Beemer Club
www.airheads.org
The Beautiful Black Hills of South Dakota
75 R90/6, 03 KLR650, 79 R100RT
rear shock setting
Posted: Thu Nov 22, 2007 6:48 am
by Doug Pippin
The real problem is that the KLR comes with a inadequate rear shock spring.
You still need to move the license plate to a higher location but to
make the KLR handle properly your looking at a new rear shock or at
the very least a shock spring.
There are a few rear shocks on the market.
I've installed a Cogent Dynamics shock and have been very happy with it.
If you call Rick at Cogent he can customize the shock for your riding
style and weight. With a proper shock on the bike it will handle well
both on and off road.
Check out the Cogent shock at:
http://tinyurl.com/2bg95f>
http://tinyurl.com/2bg95f
Doug Pippin
----------
At 07:18 AM 11/22/2007, you wrote:
>rear shock setting
> Posted by: "gust0261" gustavson.michael@... gust0261
> Date: Wed Nov 21, 2007 7:18 pm ((PST))
>
>Should I follow the recommendations from the manual that came with
>my 07 klr 650 or put the shock settings at a higher number? I ask
>because I have hit my license plate with the wheel 4 or 5 times now.
>the last time it was torn off. I want to be safe on the road but
>have it work like a dirt bike off road as I do ride off road most of
>the time. I don't want to make it more dangerous on the road
>though. I don't mind crashing in the dirt but I don't really want
>to while on the road.
----------
Doug Pippin
828-684-8488
d_pippin_89@...
----------
[Non-text portions of this message have been removed]
rear shock setting
Posted: Thu Nov 22, 2007 6:58 am
by revmaaatin
--- In
DSN_KLR650@yahoogroups.com, "Jud Jones" wrote:
wrote:
> >
> > Should I follow the recommendations from the manual that came
with my
> > 07 klr 650 or put the shock settings at a higher number? I ask
> > because I have hit my license plate with the wheel 4 or 5 times
now.
> > the last time it was torn off. I want to be safe on the road but
have
> > it work like a dirt bike off road as I do ride off road most of
the
> > time. I don't want to make it more dangerous on the road
though. I
> > don't mind crashing in the dirt but I don't really want to while
on
> > the road.
> >
>
> Adjust your preload so that the rear sags about 3" from fully
extended with you and your
> luggage seated on the bike. Relocate your license plate to the rear
fender, just below the
> taillight; use a Dremel to remove the inner fender. You could just
bend your plate out to clear
> the wheel, or mount it in the lower holes, but sooner or later your
tire will likely eat the inner
> fender and force you to relocate the plate anyway.
>
Additionally, you will find this also helpful
http://www.bigcee.com/klr650faq.html
revmaaatin.
rear shock setting
Posted: Thu Nov 22, 2007 7:07 am
by Michael Nelson
On Thu, Nov 22, 2007 at 07:44:30AM -0500, Doug Pippin wrote:
> I've installed a Cogent Dynamics shock and have been very happy with it.
> If you call Rick at Cogent he can customize the shock for your riding
> style and weight. With a proper shock on the bike it will handle well
> both on and off road.
>
> Check out the Cogent shock at:
> http://tinyurl.com/2bg95f>
http://tinyurl.com/2bg95f
I couldn't agree more. Thanks to Doug for initially letting me know about
the Cogent Dynamics stuff and Rick Tannenbaum. I now have the CD shock in
the rear, and CD springs + Racetech Cartridge Emulators in the front, and it
has absolutely transformed the bike. I'm finally a happy camper,
suspension-wise!
Michael
--
"It's not what I don't understand about religion that bothers me, it's what
I do understand." -- Mark Twain
San Francisco, CA
rear shock setting
Posted: Fri Nov 23, 2007 9:05 am
by Craig
The easiest way I found to relocate the license plate is to just move it from being bolted to the top bolts to bolting to the bottom bolts. I'ts a tight fit and trimming may be neccesary, but you can retain the light and stay legal.
[Non-text portions of this message have been removed]
the birkshire triple
Posted: Tue Aug 28, 2012 11:21 am
by Skypilot
My club, the Birkshire Trail Riders, is having our fall ride Sept 16th and it offers something for all KLRs. The Trail Ride would be well suited to a KLR250 or someone with a WELL tuned for off road 650 only. The Adventure ride is perfect for ANY 650 and the route is beutiful. The Dual Sport offers a little more off road centric riding than the Adventure ride and has some hero sections if you want more.
Anybody on this interested and who needs a local hand arranging things or finding accomodations please feel free to contact me directly at skypilot@....
http://www.advrider.com/forums/showthread.php?t=809360
rear shock setting
Posted: Wed Aug 29, 2012 8:53 am
by bryanonfire
Hi,
I would look this up in the old posts if I could, but I have very limited internet access.
Just bought an early E model in the Czech Republic and it looks to be in good shape. I will be riding with rider plus gear weighing in at about 250 - 260 pounds but sometimes may have a passenger on the back bringing the weight up to 400. It will be almost entirely road miles, just an occasional pothole or speed bump to worry about.
What rear shock pre-load setting do I want, and how do I set it? I know where the fitting is but remember reading something about only turning one way. The Clymer manual says very little. It is on 1.5 right now.
Same question about the rebound dampening.
Thanks
Bryan