Wilsons Sandbox
http://frenchandlogan.com/phpBB3/
http://frenchandlogan.com/phpBB3/viewtopic.php?f=52&t=269635
--- In DSN_klr650@y..., richardm@g... wrote: > I found this replacement turn signal flasher at Autozone that claims > to be a "loud" turn signal flasher. It even has a little remote kit > that can be used to mount the flasher in a more audible location. > Anyone ever try this little gizmo out? I wonder if it would be loud > enough to hear on a moto. > > RM
I think you'll need a three-prong flasher. I used an EP34 (Tridon-Stant) when I went to two-filament bulbs (heavier load, but I think the concept is the same). I think any solid-state/variable-load 3-prong flasher will work. The third prong is a ground, so it's easy to wire. (The stock connector will fit on the other two prongs.) Krokko -- Dr. J. Christopher Krok John Lucas Adaptive Wind Tunnel Caltech MS 205-45, Pasadena, CA 91125> From: Tengai Mark Van Horn > Subject: Once Again, flasher for LED Turn Sigs > > Alright, so I switched to LED turn signals. I was told that an EL12 > two-prong flasher will work. It works with two LEDs and two > incandescents, but not with four LEDs. > What flasher do I need to make this work?
-- Chris Long Chris.M.Long@...On Fri, Dec 11, 2009 at 11:15 AM, k650 wrote: The KLR uses a two prong flasher. There is plenty of room for a larger than stock unit that can be secured with a nylon tie strap. The two prong type may be hard to find but the three prong type can be used if you add a ground wire to the third prong. You can find them at just about any auto parts store. Ask for an electronic flasher that is LED approved like the one in the link below or just buy that one. It is a bit overpriced but it works and comes with the ground wire and good instructions. I have this same one on my KLR. Walt http://cgi.ebay.com/ebaymotors/LED-bulb-turn-signal-hazard-flasher-relay-load-resistor_W0QQcmdZViewItemQQhashZitem53dcb2f572QQitemZ360185001330QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories [b]From:[/b] DSN_KLR650@yahoogroups.com [mailto:DSN_KLR650@yahoogroups.com] [b]On Behalf Of [/b]E Hines [b]Sent:[/b] Friday, December 11, 2009 11:57 AM [b]To:[/b] DSN [b]Subject:[/b] [DSN_KLR650] Turn signal flasher Anyone know of a good aftermarket flasher the works on the KLR with LED lights. I would like one designed to fit in the current location. Thanks.
--- In DSN_KLR650@yahoogroups.com, E Hines wrote: > > Yes, it is. You can order one from Fred. They are reusable locking nut that allow's you to throw away the locking washer. I will verify the nut size on mine, but I thought it was a 30 mm. Let you all know for sure later. > > > > > ________________________________ > From: Steve > Cc: DSN DSN_KLR650@yahoogroups.com> > Sent: Sat, December 5, 2009 1:22:56 AM > Subject: Re: [DSN_KLR650] 30mm wrench on KLR > > > Ok, this sounds encouraging, by "front counter sprocket nut" do you mean > the "stock front chain sprocket nut"? And what is the "jake" nut? > I want to change my front sprocket to 14T, will this size wrench work? 30mm? > Bet you guys get annoyed by these new owners, don't ya? > Steve > Chico > A19 > > > E Hines wrote: > > >Front counter sprocket nut. The jake nut is the same size. > > > > > > > > > ________________________________ > > > > >Can anyone tell me *where* this size wrench will fit *where* on my A19? > >I know that sounds weird but what will it fit on my KLR? > >30 mm. > >Believe me, there is a method behind my logic on this question. > > > >Chicobro > >A19 > > >