Wilsons Sandbox

Posted: **Sat Aug 29, 2009 11:51 pm**

Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order, or if they can be found in any hardware store. I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar I am building. TIA Randy from Burbank [Non-text portions of this message have been removed]

Posted: **Sun Aug 30, 2009 4:05 am**

I don't know if the KLR is different from every other bike I've worked on, but normally they're standard Nylock nuts. -Jeff Khoury Astatic Solutions, LLC.

----- Original Message ----- From: "Randall Marbach" To: "KLR Group" DSN_klr650@yahoogroups.com> Sent: Saturday, August 29, 2009 9:50:48 PM GMT -08:00 US/Canada Pacific Subject: [DSN_KLR650] Front Disk Rotor Bolts Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order, or if they can be found in any hardware store. I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar I am building. TIA Randy from Burbank [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]

Posted: **Sun Aug 30, 2009 9:57 am**

Nope, the nylock nuts are for the rear sprocket. The rotor bolts have a shoulder that center them in the mounting holes on the disc. I've never tried to source them so I can't be of much help there. But if you have a local place with a decent selection of metric hardware, why not just pull one from your front wheel when you get to the store and see what the friendly folks have to say about a match. da Vermonster

--- In DSN_KLR650@yahoogroups.com, Jeff Khoury wrote: > > I don't know if the KLR is different from every other bike I've worked on, but normally they're standard Nylock nuts. > > -Jeff Khoury > Astatic Solutions, LLC. > > ----- Original Message ----- > From: "Randall Marbach" > > Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order, > or if they can be found in any hardware store. > > I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar > I am building. > > TIA > > Randy from Burbank >

Posted: **Mon Aug 31, 2009 5:33 pm**

--- In DSN_KLR650@yahoogroups.com, Randall Marbach wrote: I have only found them from the dealer. > > Does anybody know if the 9 bolts that hold the front disk to the front hub on an A17 are special order, > or if they can be found in any hardware store. > > I need a set to mount a KLR front rotor to a KLR front hub to used as part of a wheel assembly on a sidecar > I am building. > > TIA > > Randy from Burbank > > > > > > [Non-text portions of this message have been removed] >

Posted: **Mon Aug 31, 2009 7:20 pm**

yes carb was removed and replaced with a known good one. choke cable was replaced at the same time with a different one. klr6502k -- In DSN_KLR650@yahoogroups.com, Richard Decker wrote:

> > Sounds to me like your choke is stuck on. Have you tried removing the choke > cable? It could be that it's stuck and pulling your choke slightly. > > On Mon, Aug 31, 2009 at 10:39 AM, klr6502k wrote:

Wilsons Sandbox

2000 klr will not idle or run under 2500 rpm

front disk rotor bolts

front disk rotor bolts

front disk rotor bolts

front disk rotor bolts

2000 klr will not idle or run under 2500 rpm