Page 1 of 1
klr650-- *** main jet ***
Posted: Thu Jun 18, 2009 11:10 am
by Luc Legrain
i did the air box mod, Hi flow air filter, opened up the stock pipe took the spark cone out, enlarge the baffle hole and 21/2 inches stub . Loud but not annoyingly loud.
--- On Thu, 6/18/09, tomatocity wrote:
From: tomatocity
Subject: Re: [DSN_KLR650] klr650-- *** Main Jet ***
To: "Luc Legrain"
Date: Thursday, June 18, 2009, 7:01 AM
What mods have you made?
On Thu, Jun 18, 2009 at 4:58 AM, Luc Legrain wrote:
I got the DynoJet kit stage 1 and 2 from Fred. With the mods I've made I'll put the stage 2 in .
--- On Thu, 6/18/09, tomatocity wrote:
From: tomatocity
Subject: Re: [DSN_KLR650] klr650-- *** Main Jet ***
To: "Luc Legrain"
Date: Thursday, June 18, 2009, 6:56 AM
Yep. What kit did you get?
On Thu, Jun 18, 2009 at 4:32 AM, Luc Legrain wrote:
got me a re-jetting kit which I will install this w/e . I assume the " MAIN JET " is the one where the needle seats in, correct ?
Thanks
[Non-text portions of this message have been removed]
messed up
Posted: Thu Jun 18, 2009 2:58 pm
by transalp 1
Went to do the $0.22 mod this morning and I messed up.
1.) I realized I couldn't find my #4 washers *after* I'd tried to adjust the pilot screw.
2.) I dropped the screwdriver bit I was using to count the number of turns out the bike had from the factory.
I have no idea how many turns out the screw was so I can take it back to the original setting w/o doing the other mods.
Can someone tell me about how many turns the pilot screw should be out ?
If there is no general #, what can you recommend I set it at until I can get all my stuff together & try again another day?
THANKS!!
eddie
08' GL1800
09' KLR650
[Non-text portions of this message have been removed]
messed up
Posted: Thu Jun 18, 2009 3:31 pm
by transalp 1
Thanks, Larry!
After I realized I was missing washers (and given he hassle of adjusting the screw with the carb in place.)
I left the screw out 1.75 turns. We'll see how it runs on my way to work shortly. If it's not right, I'll take it back in
a bit and go from there.
Now, where *did* I put those washers.......................................................................
eddie
----- Original Message -----
From: Larry Drake
To: transalp1@...
Sent: 6/18/2009 4:25:30 PM
Subject: RE: [DSN_KLR650] messed up
I believe mind was about 1 complete turn out for stock, after the 22 cent mod it have it 1 trurns out.
Larry
From:
DSN_KLR650@yahoogroups.com [mailto:
DSN_KLR650@yahoogroups.com] On Behalf Of transalp 1
Sent: Thursday, June 18, 2009 1:58 PM
To: KLR650 list
Subject: [DSN_KLR650] messed up
Went to do the $0.22 mod this morning and I messed up.
1.) I realized I couldn't find my #4 washers *after* I'd tried to adjust the pilot screw.
2.) I dropped the screwdriver bit I was using to count the number of turns out the bike had from the factory.
I have no idea how many turns out the screw was so I can take it back to the original setting w/o doing the other mods.
Can someone tell me about how many turns the pilot screw should be out ?
If there is no general #, what can you recommend I set it at until I can get all my stuff together & try again another day?
THANKS!!
eddie
08' GL1800
09' KLR650
[Non-text portions of this message have been removed]
Please consider the environment before printing this e-mail.
This transmission, which may contain confidential information, is for the intended recipient only. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon this information by persons or entities other than the intended recipient, is prohibited. If you received this in error, please contact the sender and delete the material from your computer and networks. Thank you
[Non-text portions of this message have been removed]