Wilsons Sandbox

Mention where you are, might be somebody close-by with the holder and the puller bolt that might just let you use what they got. Might try just buying a crows foot for your ratchet, never tried but seems like it would fit. Dooden A15 Green Ape

--- In DSN_KLR650@yahoogroups.com, "ckahleer" wrote: > > I have a 11/4" combination wrench I am planning to heat and bend to > use as a rotor holder tool. > If others on the list have already done this, my questions are: > MustI make 2 90 deg bends or will 2 45 deg bends work? > After heating and bending with a butane tourch, should I let the > wrench air cool or dip it in water. I kind of remember something from > shop class about water cooling makes the metal harder. > > Craig Kahler >

On Sun, 30 Nov 2008 04:31:36 -0000 "ckahleer" writes:

> I have a 11/4" combination wrench I am planning to heat and bend to > use as a rotor holder tool. > If others on the list have already done this, my questions are: > MustI make 2 90 deg bends or will 2 45 deg bends work? > After heating and bending with a butane tourch, should I let the > wrench air cool or dip it in water. I kind of remember something > from > shop class about water cooling makes the metal harder. > > Craig Kahler

<><><><><><><><><><><> <><><><><><><><><><><> List, I sent the below note to Craig since it had attachments. But thought the info may be helpful to others so here it is below. Best, Jeff <><><><><><><> Craig, This is off list since I'm attaching three .jpgs but I will send the same info to the list without the .jpgs. I think I got my wrench dimensions from EagleMike about 4 1/2 years ago. One .jpg shows my notes from then and they are metric dimensions. The pictures of my wrench are taken to show inches but I guess you could use the metric scale if you want. There isn't a lot of room inside the rotor so I think the 90 degree bends are best. Two 45 degree bends would work in theory but I think you don't have room here. I think the most critical bend is the first one in that it isn't too far away from the rotor. In the picture mine shows about 1 3/8". Then make sure you've bent it back with at least 7/8" of height. The suggestion was 20.51mm. I think my wrench shows just over an inch. You do want the holder to clear the edge of the rotor without touching it or being on an angle. It's also helpful if the wrench on each end of the bends is parallel. That will help with transferring force and also for resting it on the footpeg while in use. If the ends aren't parallel, in use the wrench may want to twist on the rotor. The rotor is delicate and you can break one pretty easily if you aren't careful. I think you'll need more heat than is available from a butane torch. There is a lot of metal to act as a heat sink and I'm not sure you'll get the heat you'll need without adding compressed air or oxygen. You should plan on getting the metal red hot before bending. Then let it cool for a minute or two before making the second bend. If you are using an Oxy-Fuel torch I think you'll do best with a soft, neutral flame. Let the bends cool in still air. No need to quench and depending on how you might do that it could make the wrench brittle. Hope this is helpful. Best, Jeff Saline ABC # 4412 South Dakota Airmarshal Airheads Beemer Club www.airheads.org The Beautiful Black Hills of South Dakota 75 R90/6, 03 KLR650, 79 R100RT ____________________________________________________________ Click to find high quality stock photos and images. http://thirdpartyoffers.juno.com/TGL2141/fc/PnY6rw1aBm1e4eooVm67nCZE958lLSy7jOQ1cJZoyUatkpO1Iu0ks/

I have never bent a wrench but when heating my tempered drain clearing cables I cool them with oil .

----- Original Message ----- From: ckahleer To: DSN_KLR650@yahoogroups.com Sent: Saturday, November 29, 2008 10:31 PM Subject: [DSN_KLR650] Making a rotor holder tool I have a 11/4" combination wrench I am planning to heat and bend to use as a rotor holder tool. If others on the list have already done this, my questions are: MustI make 2 90 deg bends or will 2 45 deg bends work? After heating and bending with a butane tourch, should I let the wrench air cool or dip it in water. I kind of remember something from shop class about water cooling makes the metal harder. Craig Kahler [Non-text portions of this message have been removed]

I'd quench with oil, the hardness will go deeper. http://www.efunda.com/processes/heat_treat/hardening/direct.cfm E -- "If ye love wealth better than liberty, the tranquility of servitude better than the animating contest of freedom, go home from us in peace. We ask not your counsels or your arms. Crouch down and lick the hands which feed you. May your chains set lightly upon you,and may posterity forget that you were our countrymen." Samuel Adams, 1776